Buy or Renew
Buy or Renew
Cisco + Splunk: It’s a new day for your data. Learn more.
 
Welcome to the Community!
The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally.
New Here? Click here to learn more and get started.
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
1930360members
1246280discussions

Trending Topics

Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!

Community Activity

Start a conversation

Soft reset command for ospf

Hello, I seen a soft reset for bgp and eigrp for to have peer advertise routes. Does ospf have a soft reset or it doesn't and if so why? Thanks,

Cisco NCS 540 mpls problem and web access

Hi We recently acquired a Cisco NCS 540 router and are currently facing some challenges with MPLS testing. Despite our efforts, we are unable to access the necessary MPLS commands on the device. This leads us to believe that the required features mig...

Cisco Switch with 4G router ISP

Hello all,i have a problem.i have 4G router from ISP and the port is connected to HP switch then one of HP ports connected to my Cisco Switchwhen The power is off then on at 4G router .. the 4G router internet light became red and that's mean there i...

OSPF script stop working

Hi Team I have a script installed on cisco Device ASR 9K. It's working before but suddenly it stopped.I try to delete it and re-send it also delete event then re-conf it  but doesn't work.Could you please help me to solve the issue?   

Sonia by • Level 1
  • 119 Views
  • 1 replies
  • 0 Helpful votes

Web Application Server

Dear Community,I'm asking for you guidance. I have come across a challenge on Cisco ASA version 9.8. Need to allow a web server to be access outside(Public) from DMZ Zone to Ouside Zone.  Per below configuration template. Nat is transilating but acce...

dissai by • Level 1
  • 484 Views
  • 20 replies
  • 0 Helpful votes

Stack switch replacement with different model switch.

Hi,   I have two  WS- c3750x-48T -L switches stacked - connected back to back with  Stack cable. Now one of the switch failed and I have only  WS- c3750X- 12 S stackable switch as SPARE  with me. So can replace 48 Port with 12 Port ?  Does it need an...

CiscoAAA1 by • Level 1
  • 99 Views
  • 2 replies
  • 0 Helpful votes

Cannot log into vManage GUI

Hi I am trying to set vManage, vBond, vSmart and vEdge on a VMWare Workstation virtual environment on my pc. I successfully installed vManage first. I can ping vManage vpn 512 ip from the host however, I cannot connect to the web GUI. I get back and ...

image.png
rudimocnik by • Level 1
  • 13066 Views
  • 12 replies
  • 10 Helpful votes

Monitoring of Catalyst/DNA Center itself

Hi,I wonder which is the best way to monitor our DNA Center appliance. We have all our networking infrastructure monitored and we want to have DNA Center also under this tool (from SolarWinds). We usually monitor using icmp and SNMP. Is it possible t...

lecabral by • Level 1
  • 142 Views
  • 5 replies
  • 0 Helpful votes

How to stop paging of commands output on Cisco iOS devices?

Hello Community,Is there any command to turn-off the paging of the commands output on Cisco iOS and display all output without paging? On Dell Switches, there's a command "terminal length 0", but the same doesn't seem available on Cisco iOS.Router#te...

Load more